S02860

 

Tech. Sheet

 

  Brochure

  

   Hull : GRP, Fibreglass, Wooden

 

   Type: LED

 

   Power: 20W

 

   Lummen: 770

 

   Angle: Flush

     The UL Ti MATE 80, 20W LED is a “through- hull” submersible marine light rated IP68 to 10 bar. The light is suitable for small boats and can be installed into GRP-fiberglass and wooden hulls.

It must be installed below the minimum waterline.

     The boat must be hauled out for installation, although maintenance of the LED is carried out from inside the hull.

     The LEDs are available in blue, red, green or white.

     The LED driver is fitted in an IP66 enclosure and is mounted remotely.

 

S02652

 

Tech. Sheet

 

  Brochure

  

   Hull : GRP, Fibreglass, Wooden

 

   Type: Xenon

 

   Power: 55W

 

   Lummen: 4800

 

   Angle: Flush

    This is our most popular “through-hull” submersible marine light IPX8 rated to 10 bar for coastal power boats and some ten thousand have been installed world wide.

    The light is suitable for installation into GRP-fibreglass and wooden hulls and must be installed below the minimum waterline.

    The boat must be hauled out for installation, although maintenance is carried out from inside the hull.

    The light has a sealed integral igniter which makes it safer, and allows the ballast to be located away from the bilge area.

   The latest UL Ti MATE 80 can also be fitted with a wide beam lens.

 

S02652-XT

 

Tech. Sheet

 

  Brochure

  

  Hull : GRP, Fibreglass, Wooden

 

  Type: Xenon

 

  Power: 55W

 

  Lummen: 4800

 

  Angle: Flush

    In response to customer demand we have designed a new extended version of theUL Ti MATE 80. The length of the light barrel has been increased, so the maximum hull thickness is now 110mm instead of 65mm.

    The light is suitable for installation into GRP-fibreglass and wooden hulls and must be installed below the minimum waterline. The boat must be hauled out for installation, although maintenance is carried out from inside the hull.

    The light has a sealed integral igniter which makes it safer, and allows the ballast to be located away from the bilge area.

    The latest UL Ti MATE 80 can also be fitted with a wide beam lens as shown in picture.

 

S02655

 

Tech. Sheet

 

  Brochure

  

  Hull : GRP, Fibreglass, Wooden

 

  Type: Halogen

 

  Power: 100W

 

  Lummen: 750

 

  Angle: Flush

     This ”through-hull” submersible marine light IPX8 rated to 10 bar, is suitable for smaller boats.

     The light is used into GRP-fibreglass and wooden hulls and must be installed below the minimum waterline.

     The boat must be hauled out for installation, although maintenance is carried out from inside the hull.

    This UL Ti MATE 80 uses a 100w halogen lamp and runs on 12 or 24 VDC.

 

S00475 SA 150W

 

Tech. Sheet

 

  Brochure

  

Hull : GRP, Fibreglass, Wooden

 

Type: MSD Metal Halide

 

Power: 150W

 

Lummen: 12000

 

Angle: Flush

   This is the most flexible and powerful “through-hull” submersible marine light for the large sports fish yachts and is suitable for GRP-fibreglass and wooden hulls.

    The design and development of the UL Ti MATE 130 SA gave the marine market their wish with the internal adjustment (SA) which allows the beam angle to be varied from a narrow to wide beam and to universally move the beam direction by 20 degrees from within the projector housing.

    The UL Ti MATE 130 SA has a larger aperture which increases the light output by 25%. We advise that the light be installed 250mm below the minimum waterline.

    The boat must be hauled out for installation, although maintenance of the light is carried out from inside the hull.

    The light is IPX8 to 10 bar.

 

S00475 SA 250W

 

  Tech. Sheet

 

  Brochure

  

Hull : GRP, Fibreglass, Wooden

 

Type: MSD Metal Halide

 

Power: 200W

 

Lummen: 19000

 

Angle: Flush

    This is the most flexible and powerful “through-hull” submersible marine light for the large sports fish yachts and is suitable for GRP-fibreglass and wooden hulls.

    The design and development of the UL Ti MATE 130 SA gave the marine market their wish with the internal adjustment (SA) which allows the beam angle to be varied  from a narrow to wide beam and to universally move the beam direction by 20 degrees from within the projector housing.

   The UL Ti MATE 130 SA has a larger aperture which increases the light output by 25%. We advise that the light be installed 250mm below the minimum waterline.

    The boat must be hauled out for installation, although maintenance of the light is carried out from inside the hull. The light is IPX8 to 10 bar.

 

S00300 75 SA 150

 

    Tech. Sheet

 

      Brochure

  

   Hull : Steel

 

   Type: MSD Metal Halide

 

   Power: 150W

 

   Lummen: 12000

 

   Angle: Flush

     This is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

     Our patent pending internal SA ( Super Adjustable) unit allows the beam angle to be varied from a narrow to wide beam, and to universally move the beam direction by 20 degrees from within the projector housing. We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models- Flush, 30 degree and 50 degree.

   The UL Ti MATE 75 SA has a larger aperture which increases the light output by 25%. The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar.

  The aluminium model is IPX8 to 10 bar.

 

S00330 75 SA 150

 

   Tech. Sheet

 

      Brochure

  

   Hull : Steel

 

   Type: MSD Metal Halide

 

   Power: 150W

 

   Lummen: 12000

 

   Angle: 30 degrees

 

 

This is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

     Our patent pending internal SA ( Super Adjustable) unit allows the beam angle to be varied from a narrow to wide beam, and to universally move the beam direction by 20 degrees from within the projector housing. We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models- Flush, 30 degree and 50 degree.

     The UL Ti MATE 75 SA has a larger aperture which increases the light output by 25%. The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar.

The aluminium model is IPX8 to 10 bar.

 

S00350 75 SA 150

 

    Tech. Sheet

 

      Brochure

  

   Hull : Steel

 

   Type: MSD Metal Halide

 

   Power: 150W

 

   Lummen: 12000

 

   Angle: 50 degrees

 

     This is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

     Our patent pending internal SA ( Super Adjustable) unit allows the beam angle to be varied from a narrow to wide beam, and to universally move the beam direction by 20 degrees from within the projector housing. We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models- Flush, 30 degree and 50 degree.

   The UL Ti MATE 75 SA has a larger aperture which increases the light output by 25%. The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar.

The aluminium model is IPX8 to 10 bar.

 

S00300 75 SA 250

 

    Tech. Sheet

 

      Brochure

  

   Hull : Steel

 

   Type: MSD Metal Halide

 

   Power: 250W

 

   Lummen: 19000

 

   Angle: Flush

    This is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

    Our patent pending internal SA ( Super Adjustable) unit allows the beam angle to be varied from a narrow to wide beam, and to universally move the beam direction by 20 degrees from within the projector housing.

We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models - Flush, 30 degree and 50 degree.

     The UL Ti MATE 75 SA has a larger aperture which increases the light output by 25%. The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar. The aluminium model is IPX8 to 10 bar.

 

S00330 75 SA 250

 

    Tech. Sheet

 

      Brochure

  

   Hull : Steel

 

   Type: MSD Metal Halide

 

   Power: 250W

 

   Lummen: 19000

 

   Angle: 30 degrees

     This is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

      Our patent pending internal SA ( Super Adjustable) unit allows the beam angle to be varied from a narrow to wide beam, and to universally move the beam direction by 20 degrees from within the projector housing.

      We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models - Flush, 30 degree and 50 degree.

      The UL Ti MATE 75 SA has a larger aperture which increases the light output by 25%. The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar. The aluminium model is IPX8 to 10 bar.

 

S00350 75 SA 250

 

    Tech. Sheet

 

      Brochure

  

    Hull : Steel

 

    Type: MSD Metal Halide

 

   Power: 250W

 

   Lummen: 19000

 

   Angle: 50 degrees

     This is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

     Our patent pending internal SA ( Super Adjustable) unit allows the beam angle to be varied from a narrow to wide beam, and to universally move the beam direction by 20 degrees from within the projector housing.

     We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models - Flush, 30 degree and 50 degree.

     The UL Ti MATE 75 SA has a larger aperture which increases the light output by 25%. The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar. The aluminium model is IPX8 to 10 bar.

 

S00600 75 SA 150

 

    Tech. Sheet

 

      Brochure

  

   Hull : Aluminium

 

   Type: MSD Metal Halide

 

   Power: 150W

 

   Lummen: 12000

 

   Angle: Flush

     This is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

     Our patent pending internal SA ( Super Adjustable) unit allows the beam angle to be varied from a narrow to wide beam, and to universally move the beam direction by 20 degrees from within the projector housing. We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models- Flush, 30 degree and 50 degree.

     The UL Ti MATE 75 SA has a larger aperture which increases the light output by 25%. The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar.

     The aluminium model is IPX8 to 10 bar.

 

S00630 75 SA 150

 

    Tech. Sheet

 

      Brochure

  

   Hull : Aluminium

 

   Type: MSD Metal Halide

 

   Power: 150W

 

   Lummen: 12000

 

   Angle: 30 degrees

    This is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

    Our patent pending internal SA ( Super Adjustable) unit allows the beam angle to be varied from a narrow to wide beam, and to universally move the beam direction by 20 degrees from within the projector housing. We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models- Flush, 30 degree and 50 degree.

    The UL Ti MATE 75 SA has a larger aperture which increases the light output by 25%. The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar.

   The aluminium model is IPX8 to 10 bar.

 

S00650 75 SA 150

 

    Tech. Sheet

 

      Brochure

  

   Hull : Aluminium

 

   Type: MSD Metal Halide

 

   Power: 150W

 

   Lummen: 12000

 

   Angle: 50 degrees

    This is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

    Our patent pending internal SA ( Super Adjustable) unit allows the beam angle to be varied from a narrow to wide beam, and to universally move the beam direction by 20 degrees from within the projector housing. We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models- Flush, 30 degree and 50 degree.

    The UL Ti MATE 75 SA has a larger aperture which increases the light output by 25%. The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar.

    The aluminium model is IPX8 to 10 bar

  

S00600 75 SA 250

 

    Tech. Sheet

 

      Brochure

  

   Hull : Aluminium

 

   Type: MSD Metal Halide

 

   Power: 250W

 

   Lummen: 19000

 

   Angle: Flush

    This is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

    Our patent pending internal SA ( Super Adjustable) unit allows the beam angle to be varied from a narrow to wide beam, and to universally move the beam direction by 20 degrees from within the projector housing.

    We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models - Flush, 30 degree and 50 degree.

    The UL Ti MATE 75 SA has a larger aperture which increases the light output by 25%. The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar. The aluminium model is IPX8 to 10 bar.

 

S00630 75 SA 250

 

    Tech. Sheet

 

      Brochure

  

   Hull : Aluminium

 

   Type: MSD Metal Halide

 

   Power: 250W

 

   Lummen: 19000

 

   Angle: 30 degrees

     This is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

     Our patent pending internal SA ( Super Adjustable) unit allows the beam angle to be varied from a narrow to wide beam, and to universally move the beam direction by 20 degrees from within the projector housing.

     We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models - Flush, 30 degree and 50 degree.

     The UL Ti MATE 75 SA has a larger aperture which increases the light output by 25%. The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar. The aluminium model is IPX8 to 10 bar.

  

S00650 75 SA 250

 

    Tech. Sheet

 

      Brochure

  

   Hull : Aluminium

 

   Type: MSD Metal Halide

 

   Power: 250W

 

   Lummen: 19000

 

   Angle: 50 degrees

    This is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

    Our patent pending internal SA ( Super Adjustable) unit allows the beam angle to be varied from a narrow to wide beam, and to universally move the beam direction by 20 degrees from within the projector housing.

    We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models - Flush, 30 degree and 50 degree.

    The UL Ti MATE 75 SA has a larger aperture which increases the light output by 25%. The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar. The aluminium model is IPX8 to 10 bar.

 

S00360 75 WT 150

 

    Tech. Sheet

 

      Brochure

  

   Hull : Steel

 

   Type: MSD Metal Halide

 

   Power: 150W

 

   Lummen: 12000

 

   Angle: Flush, 30 deg. or 50 deg.

    This is a “through-hull” submersible marine light for welding into steel hulls. This light has been specially designed for installation and operation in fresh or seawater ballast tanks.

     It is not recommended to fit these lights in fuel oil tanks or hazardous areas. The boat must be hauled out for installation, although maintenance of the light can be carried out from inside the tank. Please allow access for maintenance.

We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water and that the light be angled 15 deg downward. To achieve this there are 3 weld-ins - Flush, 30 degree and 50 degree.

     The light has a stainless steel watertight projector case which screws onto the insert. The standard S.S. inserts are purchased separately. The hydraulic hose and cable are used to route the cable from the ballast to the projector. The hose and cable length must be specified and these are ordered separately.

 

S00360 75 WT 250

 

    Tech. Sheet

 

      Brochure

  

   Hull : Steel

 

   Type: MSD Metal Halide

 

   Power: 250W

 

   Lummen: 19000

 

   Angle: Flush, 30 deg. or 50 deg.

     This is a “through-hull” submersible marine light for welding into steel hulls. This light has been specially designed for installation and operation in fresh or seawater ballast tanks.

     It is not recommended to fit these lights in fuel oil tanks or hazardous areas. The boat must be hauled out for installation, although maintenance of the light can be carried out from inside the tank. Please allow access for maintenance.

     We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water and that the light be angled 15 deg downward. To achieve this there are 3 weld-ins - Flush, 30 degree and 50 degree.

    The light has a stainless steel watertight projector case which screws onto the insert. The standard S.S. inserts are purchased separately. The hydraulic hose and cable are used to route the cable from the ballast to the projector. The hose and cable length must be specified and these are ordered separately.

 

S00300 75 150

 

      Brochure

  

   Hull : Steel

 

   Type: MSD Metal Halide

 

   Power: 150W

 

   Lummen: 12000

 

   Angle: Flush

     The UL Ti MATE 75 Fixed is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

     It does not include the SA 'Super Adjustable' unit and has been introduced to compete fairly with other fixed lights on the market. The lens aperture is exactly the same as the SA to give the same maximum light output.

     This new light is also shorter in length to the SA unit so that it is easier to fit into those small areas.

     We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models - Flush, 30 degree and 50 degree.

    The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar. The aluminium model is IPX8 to 10 bar.

 

S00350 75 150

 

      Brochure

  

   Hull : Steel

 

   Type: MSD Metal Halide

 

   Power: 150W

 

   Lummen: 12000

 

   Angle: 50 degrees

      The UL Ti MATE 75 Fixed is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

      It does not include the SA 'Super Adjustable' unit and has been introduced to compete fairly with other fixed lights on the market. The lens aperture is exactly the same as the SA to give the same maximum light output.

      This new light is also shorter in length to the SA unit so that it is easier to fit into those small areas.

      We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models - Flush, 30 degree and 50 degree.

     The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar. The aluminium model is IPX8 to 10 bar.

 

S00600 75 150

 

      Brochure

  

   Hull : Aluminium

 

   Type: MSD Metal Halide

 

   Power: 150W

 

   Lummen: 12000

 

   Angle: Flush

     The UL Ti MATE 75 Fixed is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

     It does not include the SA 'Super Adjustable' unit and has been introduced to compete fairly with other fixed lights on the market. The lens aperture is exactly the same as the SA to give the same maximum light output.

     This new light is also shorter in length to the SA unit so that it is easier to fit into those small areas.

     We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models - Flush, 30 degree and 50 degree.

      The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar. The aluminium model is IPX8 to 10 bar.

 

S00630 75 150

 

      Brochure

  

   Hull : Aluminium

 

   Type: MSD Metal Halide

 

   Power: 150W

 

   Lummen: 12000

 

   Angle: 30 degrees

     The UL Ti MATE 75 Fixed is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

     It does not include the SA 'Super Adjustable' unit and has been introduced to compete fairly with other fixed lights on the market. The lens aperture is exactly the same as the SA to give the same maximum light output.

     This new light is also shorter in length to the SA unit so that it is easier to fit into those small areas.

     We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models - Flush, 30 degree and 50 degree.

     The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar. The aluminium model is IPX8 to 10 bar.

 

S00650 75 150

 

      Brochure

  

   Hull : Aluminium

 

   Type: MSD Metal Halide

 

   Power: 150W

 

   Lummen: 12000

 

   Angle: 50 degrees

      The UL Ti MATE 75 Fixed is a “through-hull” submersible marine light for welding into aluminium and steel hulls. Maintenance of the light is carried out from inside the hull.

      It does not include the SA 'Super Adjustable' unit and has been introduced to compete fairly with other fixed lights on the market. The lens aperture is exactly the same as the SA to give the same maximum light output.

      This new light is also shorter in length to the SA unit so that it is easier to fit into those small areas.

      We advise that the light be installed 250mm below the minimum waterline when the yacht is loaded with 50% fuel and 50% water, and that the light be angled 15 degrees downwards. To achieve this there are 3 models - Flush, 30 degree and 50 degree.

     The stainless steel model comes as standard with Ice Class Lloyds Approval and has been pressurised to 80 bar. The aluminium model is IPX8 to 10 bar.